KIJIMA

I was looking for a blinker for my ZX-10R that doesn't have too much of a blinker body.The famous one is Kellerman, but that one is too expensive.Moreover, the vehicle itself is a Design with an Edge,...

I used it on my XL1200C SPORTSTER 1200. the tank is thin and the footpeg is on the outside, so I didn't have any relation with the knee grip, but it makes the knee grip easier and more stable. I bough...

I used it on XL1200C SPORTSTER 1200. The brake pedal is placed in the inside of the footpeg compared with the Japanese car. So I had to be conscious of the inner thigh and braking until I got used to ...

This is a cheap and easy way to improve the look of the Axle end, which looks like a bare steel pipe. It's just a simple fit, but it's ExactlyFit so it's unlikely to come off.

I don't usually carry a lot of large luggage, so I was looking for a smaller carrier and found this one. It's just what I needed.I'm very happy with the large size, and most importantly, the sporty lo...

The mount type parts that can be installed on BirdCity are1.Type with Mount bar near the Handle using Mirror mounting hole.2.Type with Mount bar on the top side of Meter using Screen mounting part.The...

The Helmet Lock Assist Alpha will allow you to use the helmet that used to be difficult to hang on the Helmet Holder. Different and satisfying.

[How is it used?installedWas the one you received as per Image?It was just as Image.Was the installation difficult?It was easyHow was your experience with it?It looks better and my passengers feel mor...

It's a pompous design only because of Exclusive Design.Unfortunately, we don't have a side bag at the moment, so we haven't been able to test its performance.It's a slender material, with modest self-...

Since the color of the brake lever was changed to Black, I changed the Clutch to Black as well.I chose the KIJIMA Clutch lever for the Custom because I wanted to make it look like OEM.Looks passable. ...

Can be popped on. Can be attached quickly.I put it on my wife's cbr250r.I let my partner do the installation work, and even a woman who is not used to machines or DIY could do the installation work wi...

I always put it on every time I change my car model.It's a product I can't do without anymore.

The strength and the stability of the installation place are not felt well. As for the feeling of use, because the Inner cover is raised in the Center, Helmet hits easily and is worried about the scra...

Many OEM helmet holders are in an awkward position, but this product that can be fixed to the lever holder is very convenient. I installed it in Left Side which is easy to use. The color is black, so ...

Helmet holder is not attached, so I installed it.Easy to install, ready to use!

This is a safe and easy way to return the Caliper piston to its original position when replacing brake pads, without damaging the Caliper Seal because it applies even force to the piston instead of fo...

Purchased the DL1000 V-STROM250's Front Blinker in an attempt to position it. As a result, a good place for the installation of Relay became the inside of the part of Shroud style, the waterproofing t...

It can be used to adjust the level of oil in the reservoir for brake fluid and clutch fluid and to remove the fluid from the reservoir.

The most commonly used Size is Quantity:It is a small part, but it is often used in very important places. [Contents] I'm happy if it is.

"Yamaha Yamalube Wire grease Together with.Nozzle fits the bill!Although the wire was not completely pinched and leaked a little, it was possible to chain-clean with no problem in Large sturdy degree ...

The Pad is soft and the mesh fabric does not steam It's very comfortable to wear But if you wear them underneath the Exactly Pants, when you sit or stand, the Gap comes

It is still useful to have a smartphone or USB power supply installed in Motorcycle.When exchanging, because there is a case that the Spanner touches the tank excessively, I think that it is good to p...

Also in the fixed part of the Handlebar, Screw Lock is used in NINJA, and it was hard to remove the fixed Screw. I can use it without problems at all in terms of products. Long term Spec. By aged dete...

I wanted to attach the USB terminal and Smartphone Holder to the front so I bought it.Large Incorporation made well and rigidity is neat.However, if you do not first image what you install, it may be ...

YXF-R25 - Since it is R3Exclusive Design, we replace Bolt, which has fixed OEMHandlebar, with Quantity : Pair (for Left and Right) If you remove one by one, you can easily install. I think that it wil...