Plná sada s nástavbou / Šrouby potřebné pro instalaci.
Navíc Množství: Prodáváme pouze omezenou výhodu Zadní boxVnitřní je připevněn.
■ Zadní nosič s 4 sdílenými modely je dokončen.
Yamaha YZF-R25 a YZF-R3, MT-25 a MT-03 mají společný motor a rám. Složení karoserie je mírně odlišné, ale lze jej přizpůsobit na 4 modely automobilů.
YZF-R25, který přijal Cowling a Design připomínající SUPER SPORTS 750 a MT-25, který následuje sérií řady STREETFIGHTER. Oba vozy jsou Slim a Sharp Image a Motorcycle, které jsou atraktivní a lehké.
Zadní nosič je praktické součásti, ale navrhnul jsem to co nejvíce, abyste nezničili Sharp Image.
■ Navržen jako ostrá, pokud je to možné, při zajištění prostoru pro cestující.
Zpočátku jsem se snažil zkontrolovat zadní nosný rám na sedadlo SeatLimit tak, aby nedošlo ke zničení těsného obrazu se Sharpem. Byl navržen tak, jak jsem zamýšlel, ale jak jsem se snažil sedět na pasažiře, dostal jsem se do stísněného stavu.
Takže jsme jej navrhli poněkud širší než původní vzorek, takže i dobrý muž, který sedí na sedadle spolujezdce, si to dovolil, dokončil jsem to jako těsný, aniž bych obětoval pohodlí spolujezdce.
■ Maximální velká zatížení je 5 kg. Každou část posilujeme.
Nedávno, dokonce i ve vozidlech, které zobrazovaly SUPER SPORTS 750 Zadní nosič a zadní box Množství: Obvykle se instaluje se sada Set.Large texture Zadní box má hmotnost asi 5kg, takže jsme každou část vyztužili tak, aby maximální velká zatížení 5kg.
Umístění výztuže Umístěte výztužnou desku do části rámu, kde je namontován zadní nosič, a také do nožní části těla položte výztuž.
■ Lomený tvar, který zdůrazňuje praktičnost a design.
Zadní skříň Existuje možnost, že víko bude uzavřeno bez povolení, pokud je víko otevřeno vodorovně nebo je víko otevřeno při otevření tělesa zadního nosiče tak, že těleso zadního nosiče má tvar, který stoupá dozadu. Jedná se o design s jednotou, který se přizpůsobuje úhlu zadního krytu.
Instalace se provádí odstraněním lišty z MT-25/03. Ačkoli je nutné vyvrtat část zadního krytu v YZF-R25 / 3, je navržena tak, aby vrtání krytu bylo nejmenší. Máme také vzorek papíru, takže pozice vrtání je snadno pochopitelná.
Full set with base and screws required for installation.
In addition, the set comes with a limited edition rear box inner.
■The rear carrier for the same four models is available.
Yamaha's YZF-R25 and YZF-R3, MT-25 and MT-03 each share the same engine and frame.Although the vehicle configuration is slightly different, World Walk has developed a rear carrier that can be adjusted to fit four different models.
The YZF-R25 has a cowling and design reminiscent of supersports, while the MT-25 follows the image of a street-fighter.Both bikes have a slim, sharp image and are lightweight with powerful performance.
The rear rack is a practical part, but World Walk designed it not to destroy the sharp image as much as possible.
■Designed to be as sharp as possible while retaining space for the passenger.
In order to keep the sharp and tight image of the bike, the frame of the rear rack was brought up to the very edge of the seat.The design of the vehicle is as World Walk wanted, but it is too tight for the passenger to sit on.
The passenger seat was designed to be slightly wider than the first sample to allow room for a larger man to sit in the passenger seat.It is a tight fit without sacrificing passenger comfort.
■Maximum loading capacity is 5kg.World Walk is reinforcing every part of it.
Recently, it has become common to install a rear carrier and a rear box as a set, even for super sports inspired vehicles.Some of the larger rear boxes weigh about 5kg, so I reinforced each part of the box and set the maximum load capacity to 5kg.
The reinforcement plate is placed on the frame where the rear carrier is installed, and also on the legs of the main body.
■The shape of the buttocks is designed for practicality and design.
When the rear box is installed, the lid may close by itself if it is horizontal or raised forward when the lid is opened.This is why the rear rack is designed to be raised backwards.The angle of the tail cowl is the same as the angle of the tail cowl, so the design has a sense of unity.
To install, remove the grab bar from MT-25 / 03.YZF-R25 / 3 requires drilling of some parts of the tail cowl, but World Walk has designed the cowl so that drilling of the cowl is minimized.A paper pattern is also included to help you know where to drill the holes.