se světelnou jednotkou
[Velikost]
šířka : Přibližně 760 mm
Délka : Přibližně 500 mm
Výška : Přibližně 520 mm
[Materiál]
FRP
Obsah produktu
Tělo krytu, sada držáků, obrazovka, sada šroubů obrazovky
* Tento kryt je produkt pro všeobecné použití vyrobený v zámoří, takže zde mohou být škrábance, škrábance a tření atd.. které by mohly způsobit, že otvory nesedí, a může být nutné jej upravit kvůli instalaci. Před zakoupením nezapomeňte pochopit následující.
* Světelná jednotka a kryt se mohou vzájemně rušit, v takovém případě je třeba odstranit interferující část krytu.
* Vidlice a kryt se mohou vzájemně rušit, takže musíte zkontrolovat rozsah pohybu levé a pravé strany a v případě rušení kryt oholit.
* Ostatní rušivé části je třeba stříhat, oholit nebo jinak zpracovat.
* Připojená jednotka světla musí být vyrobena z prodlužovacího svazku z hlavního svazku.
* Otvor mezi podpěrou a krytem se může posunout v závislosti na poloze krytu. V takovém případě musíte rozšířit otvor v krytu.
* Existují případy, kdy se otvory na obrazovce a krytu neshodují, v tomto případě musíte otvory pro obrazovku a kryt od středového otvoru krytu na vnější stranu upevnit pomocí matice studny a poté rozšířit části, které neodpovídají shoda se souborem.
* Některé šarže nemají otvor na straně krytu pro obrazovku. V takovém případě vyvrtejte otvory, aby odpovídaly obrazovce.
* Jiné způsoby zpracování než ty, které jsou zde uvedeny, nejsou k dispozici, proto prosím zkontrolujte aktuální vozidlo.
* Produkt je předmětem zpracování, takže nemůžeme přijímat vrácení zboží za nemožnost instalace.
* Před lakováním nezapomeňte produkt zpracovat a nainstalovat. Po malování nebudou přijímány žádné nároky.
* Vezměte prosím na vědomí, že specifikace produktu se mohou změnit z důvodu výrobce.
With light unit
[Size]
Width: Approx. 760mm
Front and rear length: Approx. 500mm
Height: Approx. 520mm
[Material]
FRP
Components
Cowl body, bracket set, windshield, windshield screw set
*Please make sure to read the notes before purchasing.
*7 inch projector LED headlight unit and the same type of light unit are used for the lights.
*Because this cowl is a universal product made non Japanese, it may have some scratches and scuffs, and the holes may not fit, so some modification is required for installation.Please make sure you understand the following information before purchasing.
*The light unit and cowl may interfere with each other, in which case it is necessary to shave the interfering part of the cowl.
*There is a case that the fork and the cowl interfere with each other, check the range of movement of both sides and if it interferes, it is necessary to shave the cowl.
*Other interfering parts need to be cut or shaved.
*The supplied light unit requires an extension harness to be fabricated from the main harness.
*Depending on the positioning of the cowl, the hole between the bracket and the cowl may be misaligned.To do this, you will need to widen the hole in the cowl.
*In some cases, the holes of the windshield and the cowl do not match, in that case, you need to fix the windshield with the well nut from the center hole of the cowl to the outside, and widen the holes with a file in order.
*Depending on the lot, some of them do not have the hole for the windshield on the cowl side.In this case, please drill the holes in order to match the windshield.
We will not provide information about processing methods other than those mentioned here, so please verify according to your actual bike.
*Any returns will not be accepted due to inability to install the product.
*Please be sure to process and install before painting.Any claims after painting are not accepted.
*There may be changes in product specifications due to the manufacturer's reasons.