Materiál: Měď
pro kladiva Thor Soft
Vyrobeno ve Velké Británii
Φ 25mm
brutto hmotnost: 90 g
* 1: Před poškozením hlavy je nutné vyměnit čelo kladiva. Nejprve zkontrolujte, zda není poškozená rukojeť. Pokud je poškozený, musí být nahrazen jedním z následujících správných rozměrů, tvarů a typů rukojetí. Také se ujistěte, že rukojeť není uvolněná v hlavě. Pokud je rukojeť uvolněná, musí být pokud možno znovu chráněna nebo vyměněna.
* 2: Vystřihněte a odstraňte co nejvíce staré tváře. Vyvrtejte otvor ve středu obličeje, dávejte pozor, abyste nevyvrtali do obličeje. Odstraňte co nejvíce tváře pomocí spodní vrtačky nebo frézky s plochým povrchem.
* 3: V takovém případě se vám může podařit zachytit střed starého povrchu kůže a složit jej dovnitř.
* 4: Jakmile je starý obličej odstraněn, vložte nový obličej. Okraj musí být otevřen jen natolik, aby se nový obličej vešel. Nejlepším způsobem, jak tuto operaci provést, je kombinace správného lisu a nástroje pro otevírání / zavírání.
* 5: Když je nová tvář na místě, otočte kombinovaný nástroj a uzavřete jej kolem nové tváře pomocí příslušného lisu. Okraj by měl být opět dostatečně uzavřen, aby pevně držel obličej na místě. Při správném nasazení lze obličej otočit.
* 6: Mnoho zákazníků nahrazuje stranu kůže, ale použitá měděná strana je obzvláště obtížně odstranitelná. Měděné zásuvky mají v sobě malé drážky, které umožňují šíření mědi během používání. Měď, kterou používáme, je 99% čistá, měkká a po značném použití může houba na hlavě kladiva. Jakmile se povrch otočí, v závislosti na aplikaci vydrží měď v tomto stavu téměř neomezeně bez další deformace. Mnoho zákazníků považuje za levnější použít měděný konec k lámání.
* Vezměte prosím na vědomí, že specifikace produktu se může z důvodů výrobce změnit.
Material: copper
for Thor Soft Hammers
Made in Great Britain
Φ 25 mm
Gross weight: 90 g
*1: The face must be replaced before any damage occurs to the hammer head.First, make sure that the handlebar is not damaged.If it is damaged, it should be replaced with one of the followingCorrect size, shape and type of handle.Also make sure the handlebar is not loose in the head.If the handlebar is loosened, it must be re-protected or replaced, if possible.
*2: Cut and remove as much of the old surface as possible.Drill a hole in the center of the face, taking care not to drill into the face.Use a bottom drill or milling machine to use the flats and remove as much of the face as possible.
*3: You may be able to grab the center of the old skin surface and fold it inward in that case.
*4: After the old side is removed, insert the new side.The rim must be opened just enough for the new surface to fit.The best way to perform this operation is a combination of a suitable press and an opening / closing tool.
*5: With the new face in place, reverse the combination tool and close it around the new face with a suitable press.Again, the rim is closed enough to hold the face firmly in place.When correctly mounted, the face can be rotated.
*6: Many customers replace the skin face, but the used copper face is particularly difficult to remove.Copper sockets have small grooves in them, and the copper will enlarge during use.The copper applied to the products is 99% pure, soft, and can mushroom on the hammerhead after considerable use.In this state, depending on the application, the copper lasts almost indefinitely without further deformation once the surface has been set.Many customers find it more economical to use the copper end for destruction.
*There may be changes in product specifications due to the manufacturer's reasons.