[Materiál] součástka : 6061 Hliníkový materiál
[Typ] Kolo
[Barva] Černá / Uhlík
[Velikost]
·Délka paže : 120mm
· Šířka paží : 13mm
・Celková délka konce tyče pro montáž : 20mm
・Celková délka plochých ploch, které lze namontovat dovnitř : 18mm
· Velký límec : ID. 13.5 / od. 14.5
· Obojek malý : ID. 9 / od. 13
・Speciální ořech : M6
Krycí šroub: M6 x délka 45 mm
・Velikost zrcadla : Rozměr 94 mm x 94 mm
[Specifikace]
・Širokoúhlé konvexní zrcadlo
· Společné pro levou i pravou stranu
・Bylo získáno certifikační číslo ECE
・ Logo KIJIMA
[Množství]
· Tělo produktu : 1 ks
· Velký límec : 1 ks
· Obojek malý : 1 ks
・Speciální ořech : 1 ks
Krycí šroub: 1 ks.
[součástka]
·Návod k použití
・ Pevné konce tyče M6
*Výhled dozadu se výrazně liší v závislosti na poloze zrcátka. Proveďte zkušební jízdu za jasné oblohy a dobré viditelnosti, abyste se seznámili se změnami viditelnosti.
*Připevněte zrcátko na konec připojené tyče a upevněte jej šrouby. Celková šířka volantu (celková šířka kola) se liší v závislosti na úhlu volantu. Před sestavením instalačního obrázku změřte rozměry.
*Připojený konec tyče se upne mezi šroub M6 x 45 mm a límec a poté se instaluje zavěšením do řídítek a utažením šroubu M6 x 45 mm. Vzhledem k tomu, že většina motocyklů s konci pažby má závit pro upevnění tyče konce navařené uvnitř řidítek pažby, límcová část pro upevnění zrcátka konce tyče tohoto produktu nemusí v závislosti na motocyklu pasovat do zrcátka konce tyče. V tomto případě, pokud má být použit závit rukojeti pažby, tyč konec tohoto produktu bude nutné vyvrtat. Máte-li jakékoli dotazy, obraťte se na svého autorizovaného prodejce jízdních kol.
*Platí pro kola s řidítky o průměru 22,2 mm a průměrem 25,4 mm (1 palce) řídítka a kola s řídítky na pažbě, která nemají předem navlečené závity pro upevnění konců pažby, nebo kola s vlastními řídítky, která nebyla opatřena závitem.
*Pokud je konec tyče se závitem, je nutné vyvrtat část konce tyče, aby bylo možné použít upevňovací šroub konce tyče.
*Obrázky mohou obsahovat jiné produkty.
* Specifikace produktu se mohou změnit z důvodů výrobce.
[Material] Component: 6061 aluminum material
[Type] Round
[Color] Black / Carbon
[Size]
・Arm length: 120mm
・Arm width: 13mm
・Total length of bar end for mounting: 20mm
・Total length of flat surfaces that can be mounted inside: 18mm
・Collar large: I.D. 13.5 / O.D. 14.5
・Collar small: I.D. 9 / O.D. 13
・Special nut: M6
Cap bolt:M6 x length 45mm
・Mirror size: 94mm x 94mm
[Specification]
・Wide angle convex mirror
・Common to both left and right
・ECE certification number obtained
・KIJIMA Logo
[Quantity]
・Product body: 1 pc.
・Collar large: 1 pc.
・Collar small: 1 pc.
・Special nut: 1 pc.
Cap bolt:1 pc.
[Components]
・Instruction Manual
・M6 fixed bar ends
*Rearward visibility varies significantly depending on the mirror position.Please be sure to run a test run under clear skies and good visibility to familiarize yourself with the changes in visibility.
*Fit the mirror to the attached bar end and fix it with screws.The overall width of the steering wheel (overall width of the bike) varies depending on the steering wheel angle.Please measure the dimensions before assembling the installation image.
*The attached bar end is clamped between the M6 x 45mm bolt and the collar, and then installed by hanging it inside the handlebar and tightening the M6 x 45mm bolt.Since most of the bikes with stock bar ends have the threading for fixing the bar ends welded inside the stock handlebars, the collar part for fixing the bar end mirror of this product may not fit into the bar end mirror depending on the bike.In this case, if the threading of the stock handle is to be used, the bar end of this product will need to be bored out.If you have any questions, please consult with your authorized bike dealer.
*Applicable to bikes with 22.2mm diameter handlebars and 25.4mm diameter (1 inches) handlebars, and bikes with stock handlebars that do not have pre-threaded threads for fixing stock bar ends or bikes with custom handlebars that have not been threaded.
*If the bar end is threaded, it is necessary to bore the bar end part to use the stock bar end fixing bolt.
*Images may contain other products.
*There may be changes in product specifications due to the manufacturer's reasons.