OEM Fender is too large and too heavy in any way.
This will clean up the Design.
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
OEM Fender is too large and too heavy in any way.
This will clean up the Design.
it doesnt have a rubber or something will block the space where your signal and plate light go through. when you wash you bike the water will go into that space mt battery almost got wet . poor design.View Detail
Fits: HONDA CRF250L 20-, HONDA CRF250 RALLY 20-
When YOSHIMURA's Exhaust System is installed on CRF250L MD47, the Number and Exhaust System interfere with each other, so it cannot be installed.
MORIWAKI is EnduranceLarge sturdy.
DRC's Fender Eliminator Kit was Large sturdy even for YOSHIMURA!View Detail
Fits: KAWASAKI Ninja250 18-23 18.2-23.2[EX250P-A00101-], KAWASAKI Ninja250 23- 23.2-[EX250Y-A33611-], KAWASAKI Z400 19-22 19.2-22.9[EX400G-A32831-], KAWASAKI Z400 22- 22.9-[EX400L], KAWASAKI Z250 19-23 19.2-23.2[EX250P-A16411-]
No one has made an Impression yet.
I was hoping it would be helpful.
Was the one you received as per Image?
→As per Image
Was the installation difficult?
→As shown in the photo, all OEM parts were diverted and installed.
The Blinker is the most Large oddity, and it took a lot of time to install the Rubber parts.
About 60 minutes of work, 90 minutes to clean up.
How was your experience with it?
→ generally good
I just wish the Reflector was lower...
Fender Eliminator itself is satisfactory with no problems
[Included Parts:were they on?
→There are many OEM diversions, so not many included, they were all there!
[Was there anything that disappointed you?
None in particular.
Other items that would be helpful
? Point of installation and hang
Thin tip for Blinker removal and installation (sorry my vocabulary is limited)
Availability and clarity of Instruction Manual
I think the description is Large sturdy.
It's easy to understand, but as I keep saying, it's a blinker...
? Items to buy together
Loading Hook will be lost, so we will need to replace it.
I purchased a License PlateHook
Opinions and requests to Manufacturer
I think the Blinker is Large strange so that it cannot be easily taken off.
But go a little easier on me (laughs).View Detail
I was able to install it without any modification.
The paint quality is not bad and Material:Because it is not aluminum, it is less likely to crack due to vibration, even on single-cylinder Motorcycles.View Detail
When I installed it by myself, the most troublesome thing was to remove the Blinker from OEMFender, but it was so hard that it was troublesome.
The impression after the installation is that the Rear Fender that was sticking out to the rear is now small and tightened up.
However, because the material is steel, I think that the back side which the Small stone hits should put up Cutting sheet etc. beforehand, and the one which works from it, it will not be troubled with the measure of Rust etc. afterwards. I put up the seat of Carbon Style.
The installation time is about 1 hour if you do it in hot weather.View Detail
Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail
?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Služby zákazníkům
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING