- I bought the wrong size. I'm thinking of buying it again.Přečtěte si více
- I bought this Motorcycle used, so I replaced it with a Caliper while I was doing CaliperOH.I bought this one because the existing one had some rust.Přečtěte si více
- I've been sticking with the Tokico 6 pods. This time I adopted CaliperOverhaul and baked paint instead of OEM. I think it's a good corrosion protection. I've heard that some people use seal tape to pr...Přečtěte si více
- The OEM Bleeder Bolt is always going to Rust and Decay, so this Material:It is safer to replace it with Stainless Steel.Be sure to bleed the air and refill the fluid in the MASTER after replacement.Th...Přečtěte si více
- ZrX1200 DAEG OEMHydraulic Clutch Bleeder Bolt This Material:I replaced it with a Stainless Steel one. The OEM Bleeder Bolt is made of steel and will always rust over time, so it's best to replace it. ...Přečtěte si více
- It's a little bit expensive, but I think it's not a bad idea to change it because it's a part where corrosion is a concern. It is my personal impression that the dress-up effect is not so hopeful to b...Přečtěte si více
- I bought this as a replacement from OEMvery high (Lol) Expensive for nothing. (Lol)The color of 64Titanium material of the same size is SilverTitanium and about 1000 yen.Quantity Stainless this time:2...Přečtěte si více
- I replaced a 2006 K7 OEM BreederValve with a fluid blotch in the OEM BreederValveIt is made of stainless steel and looks greatI don't know if seal tape is necessary, but just in casePřečtěte si více
- i installed it on my bremboRCSRadial masterit's shorter in length than the brembo OEM, but the only thing shorter is the top half, so it's not a problem for useThe 10mm Wrench is useful because you ca...Přečtěte si více
- No functional problemsIt's a hobby to change from OEM as it's not used very oftenThe front brake is compatibleI installed it on a non-compliant rear brake for a test run, but the Fluid leakedThe OEM h...Přečtěte si více
- CYGNUSxInitial Model (SE12J), if it's the same Caliper model, this The product fitsI couldn't find anything that looked like a match and it was a no-go, but it was OK with no problemsIt is recommended...Přečtěte si více
- I used it in a Tokico 6-pot, and since the Screw was with me, I figured I could use it! Brake fluid leaked and it was Large Please be careful There is no problem in the productPřečtěte si více
- The shape of the tip is slightly different from OEM. I feel a sense of incompatibility when I put on Rubber cap.Seal tape winds in the reverse direction, not in the tightening direction.Noticing that ...Přečtěte si více
- Noticing that Brake fluid seeped out of Caliper's Air breederRust was amazing as I removed it. Indeed when I thought this was dangerous, I found this productReplaced. As I wrote that the installat...Přečtěte si více
- We exchanged from OEM Parts Number during Maintenance of Commuter Scooter.I checked the number of Air breeder, OEM Parts Number for Nisshin caliper and purchased it.As described in the manual, I rolle...Přečtěte si více
- We will also exchange Air breeder according to Brake fluid exchange.I confirmed ProductNo in the Parts List and confirmed its compatibility with this product and ordered it.Roll Seal tape and install....Přečtěte si více
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING